Exacq vision camera compatibility matrix. 我花了大半天的时间来搞MonoDevelop在CentOS 6.3上的安装,中间走了些弯路,因为我知道OpenSUSE中自带MonoDevelop,所以先是从OpenSUSE的packages中找glib-sharp这样的rpm包来装,但是此路不通;然后在google上疯狂找各种rpm包,期间google被河蟹n次,每次都要等上一阵才能用. Aug 24, 2018 - I tried to install mono and monodevelop on centOS 6.3. After many hours I was able to install mono but failed with monodevelop. • • • • • • Mono KDE • Welcome! If this is your first visit, be sure to check out the. You will have to before you can post in the forums. (Be aware the forums do not accept user names with a dash '-') Also, logging in lets you avoid the CAPTCHA verification when searching. Select Articles, Forum, or Blog. Posting in the Forums implies acceptance of the. • NOTICE:A Healthy openSUSE Project requires a Healthy openSUSE Board. Three Board Seats open, no Candidates yet, apply to be a Candidate. A Healthy openSUSE Project also requires a Healthy Membership Roster. If you qualify, Apply for Membership Today to qualify to Vote in the Board Elections or run as a Candidate. On Thu, 17 Dec 2009 23:36:02 +0000, elgitanito wrote: > Thanx Jim for your quick reply. > > I used to think exactly the same. But my experience. With mono is > different: > After installing Monodevelop by using Yast, its not possible to start > mono from the KDE-main-menu. The icon exists, the waitcursor starts, but > mono doesn't start. After about 20 Seconds, the wait cursor disappears > (without any message about missing libs or something like that). > > Any Idea? Try starting it from konsole and see what it spits out - chances are there's a missing dependency; usually missing libraries and such don't cause pop-up windows to display, but the output in konsole will give you the best information. Jim -- Jim Henderson openSUSE Forums Moderator. Ok, I tried starting monodevelop from the command-line. Got the information, that monodevelop wasn't installed yet (what was a reference to monodevelop 1.0. Which I had uninstalled before having installed 2.2). Well so I installed monodevelop 1.0 from the command-line beside version 2.2 in order to uninstall it within the next minute (don't ask me why I did that.). In yast only version 1.0 could be seen although both vesions have been installed one beside the other. I uninstalled md 1.0, and there were neither 1.0 nor 2.2 to be seen in yast. So I installed 2.2 again. Now it works. I have to admit that I can't tell exactly what went wrong. But as it works proper now. That doesn't matter any more:-) Next question: Is it possible to run GUI-applications, written in c# and built with monodevelop within kde4? Or do I have to have gnome installed in order to perform this? Thanx a lot guys. Ok, I tried starting monodevelop from the command-line. Got the information, that monodevelop wasn't installed yet (what was a reference to monodevelop 1.0. Which I had uninstalled before having installed 2.2). Well so I installed monodevelop 1.0 from the command-line beside version 2.2 in order to uninstall it within the next minute (don't ask me why I did that.). In yast only version 1.0 could be seen although both vesions have been installed one beside the other. I uninstalled md 1.0, and there were neither 1.0 nor 2.2 to be seen in yast. So I installed 2.2 again. Now it works. I have to admit that I can't tell exactly what went wrong. But as it works proper now. That doesn't matter any more:-) Thanx a lot guysI think the Monodevelop script you were calling before was pointing to the uninstalled version. The best way to check is open the script i.e. In your case it would have been. 'type monodevelop' which would have given you the path from where that monodevelop is being called. Open the script and check the path in it. Cara Membuat Wallpaper Bergerak Di Komputer Windows. Download wallpaper gerak untuk pc games. Setelah kalian selesai mendownload Windows7 DreamScene. Selesai Cek wallpaper kamu apakah sudah bergerak.
0 Comments
Leave a Reply. |